CSG Security NetVision Plus Guide de l'utilisateur Page 99
- Page / 164
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
21-0400E v2.3.3
Welcome Common Admin
Config
Install Tech-Ref
91
--------------------------------------------------
When finished, click [OK], and then click [X] to
close the list (upper-right corner).
Attention: To recognize any DSR Configuration
changes made while the Video Server software is
running, you may need to restart the software.
18.4
Setting up Pre-Alarm
Recording
The NetVision system can make continuous
short recordings (1 - 300 sec.) during
scheduled alarm-monitoring times, with only
the two most recent being retained at any time
(for each camera). When an alarm is
triggered, this provides a recording of the
scene just before the alarm occurred without
using up a lot of hard drive space. This
pertains to recording that is triggered by
external sensors/inputs, or video motion
detection.
TechTip: Scheduled (and manual /
instant) recording are not available while
pre-alarm recording is in effect on a
specific camera (i.e., during the scheduled
alarm/monitoring times).
Locator: (Logged in at the Video Server as
a "Supervisor"),
Select: [Utility], then [Recorder Setting].
Select Alarm , and then make your desired
selections for each camera:
--------------------------------------------------
(External Alarm Input)
To support pre-alarm recording, the external
input must be enabled for the specific camera
(even if you're using this only with video motion
detection).
External Sensor Triggered Recording: This
feature is covered separately.
(browse / previous
topic)
.
(Pre-Alarm Recording)
Enable: Select this if pre-alarm recording is to
apply to this camera.
(in sec): The duration for pre-alarm
recordings (1 - 300 sec.).
--------------------------------------------------
When finished, click [OK], and then
[Close] the utility menu.
- User's Guide 1
- Contents 3
- Copyrights and Trademarks 7
- Disclaimer 7
- Welcome to 9
- NetVision 9
- System Overview 10
- NetVision Software: 11
- Intended Audience and 12
- Required Knowledge 12
- Feature Overview 12
- Your NetVision Desktop 14
- Video Server Desktop 15
- Communications / Server 16
- Modules (Video Server) 16
- Common / Daily 17
- Remote Station: Start-up 18
- Video Server: Start-up and 18
- Logging In 18
- Logging in At a Video Server 19
- If you Need to Minimize the 19
- PTZ Control after Start-Up 19
- System I/O Primer 20
- Responding to 20
- Alarm Alerts 20
- Alarm-Alert Email 22
- (Camera Number Colours) 23
- Playback--Technical Details 25
- Overview--Types of 25
- Playback 25
- Synchronized 26
- Playback (v2.3 SP2) 26
- Bottom of the Screen 27
- Right Side of the Screen 27
- Video Search (v2.3 SP2) 28
- Top of the Screen 29
- Middle of the Screen 29
- Searching for Motion 30
- Main Portion of the Screen 31
- Working with the 32
- Playback Screen 32
- Working with the File 35
- Right-Click Menu 37
- Quad Playback 38
- File Reference 40
- Upper-Right 41
- The Utility Screen (Quad 42
- Server Management 43
- Identifying Remote Servers 43
- On this Screen 43
- Viewing Live Cameras 45
- Viewing Cameras at a Video 46
- Other PTZ Features 49
- Monitoring Cameras via TV 51
- (Spot Monitor) 51
- Recording Camera-Views 52
- Recording at a Video Server 53
- Administration 55
- Video Server Software 56
- Remote Station Software 56
- Technical Details 57
- Filekeeping (v2.3 SP2) 58
- Housekeeping 61
- Automatic Video File 62
- Management (Self 62
- Housekeeping) 62
- Video Server Users and 65
- Passwords 65
- Remote Users and 66
- Buttons in the Middle of the 67
- HTTP Server Port 68
- Viewing a List of Motion 68
- Detection Alarms 68
- Viewing Changes Made 69
- Viewing Remote User 70
- Sessions 70
- Configuration 71
- Configuration Introduction 72
- Setting Up the Alarm 74
- Alert Receiver 74
- Station List 75
- (Identifying the 75
- Video Servers) 75
- General Video Server 76
- Setting Video Playback 77
- Sessions to be Logged 77
- Alarm / Reporting Settings 78
- Set Up the 80
- Alarm Alert Caller 80
- Bottom of this Screen 81
- Auto Alarm Display 82
- Set Up Alarm Overlays 83
- Set up Cameras and Titles 85
- [Video Control] 85
- Cameras to Appear in 86
- Sequential Viewing 86
- Pan/Tilt/Zoom Activation and 87
- Show Date and Time in Video 88
- Image (Time Stamp) 88
- Enable Audio for Specific 89
- Cameras 89
- Setting the Sound Level 89
- Remote 90
- Audio Monitoring 90
- Remote Station: Initiate an 91
- Audio Monitoring Session 91
- Recording Setup 92
- Codec 93
- Priority 93
- Misc. 94
- Resolution and Recording 95
- Frame Rate for Recording 95
- Introduction to Automated 96
- Recording 96
- Schedules for Recording 96
- . Then, use one 97
- External Sensors and 98
- Recording Duration 98
- Setting up Pre-Alarm 99
- Setting up Video Motion 100
- Detection 100
- Software 101
- Installation and 101
- Network Set Up 101
- PC Requirements 102
- Remote Station 103
- General Network 106
- Requirements 106
- IP Addressing on the Network 106
- Network Services 106
- Network Ports 106
- Windows Dial-Up Networking 108
- Network Usage 109
- 21-0400E v2.3.3 110
- Reference 111
- About the Remote Module 112
- Starting the Remote Module 112
- Using the Remote Module 112
- Overview of Features 113
- Remote Configuration 114
- The WatchDog Feature 115
- Watchdog Configuration 116
- Hardware Watchdog Option 117
- Hardware Reference 118
- Camera and PTZ Reference 119
- Micro DVR 120
- PTZ Model Reference 121
- PTZ Wiring Detail 122
- Wiring Reference 123
- Open collector output 124
- High impedance at normal 124
- Also See: "25.2.3 125
- Camera Numbering…" 125
- Connection Summary— 126
- NetVision Elite 126
- Troubleshooting 127
- Using the 128
- ATM Interface Option 128
- Playing ATM Video 129
- Recordings 129
- Part 4: Buttons in the 130
- Playback Window 130
- Additional Options 131
- Viewing and Printing 131
- 'Snapshots' 131
- The Video Playback Feature 132
- (Micro DVR) 132
- Step 2: Local / Remote, and 133
- Connection Screen 133
- 3f) Old/Quad Player: 135
- Smart Motion Search 136
- Step 4: Playing a Video 137
- Introduction 141
- Requirements and Speed 141
- Concerns 141
- Items On-Screen 142
- WebView 142
- Items Under the Camera 143
- Image(s) 143
- Location of Files 144
- Title-bar and Heading Text 144
- Setting up an IP 145
- Camera or Video Server 145
- Control Panel IP / NVS 146
- Settings 146
- Additional Considerations 147
- Panoramic Video 149
- Surveillance--PVS 149
- PVS Configuration (Video 150
- Server PC) 150
- Using the PVS Control 150
- The PVS Control Screen 151
- Viewing Cameras and Playing 152
- 164
© 2020, manymanuals.fr. Tous droits réservés | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels